Presentation
JM Concept는 아날로그 입력과 출력을 분산시키고 필드 버스를 통해 데이터를 다시 전송하기 위한 인터페이스 시스템을 개발했습니다.
JM컨셉의 아날로그 신호 처리 및 격리 기술을 기반으로 한 원리입니다.
시스템은 완전히 모듈식이고 확장 가능합니다. 입력은 공정 입력뿐만 아니라 전기량, 온도(PT100, CSF가 있는 써모커플, 다른 센서의 출력) 또는 디지털 입력일 수 있습니다. 제한은 없습니다.
이 장치는 핫 플러그가 가능하며 모든 유형의 모듈을 언제든지 제한 없이 추가할 수 있습니다.
모든 측정값은 집광기로 전송됩니다. 각 유형의 필드버스에 맞게 조정된 집광기 모델이 있습니다. PLC가 진화하고 필드버스가 다르다면 집광기를 변경하기만 하면 되며 모든 수집은 동일하게 격리됩니다.

• Range

 

	Communication
	Modbus TCP	Profinet	Ethernet IP	Profibus	Modbus RTU
MIPLINE	✓
MPNLINE		✓
EIPLINE			✓
MPBLINE				✓
MRSLINE					✓

 

 

 

 

 

 

 

 

 

2 / 6

• Dimensions

 

Dimensions : width : 22,5 mm – Height : 81 mm – Depth : 98 mm

 

• Factory Settings

 

Modbus parameters		Communication speed		Synchronization		Delay at the start
		38400 bauds		Manual		0 min 0 sec
Bus parameters		Converting scenario values			On off-bus ground
		in full			The contact is closed
					Scenarios in writing maintain their value
Scenarios	Scenario 1				Scenario 2
	Slave number		101		Slave number		101
	Operation		Reading 4 floats		Operation		Writing 2 floats
	Register		6000		Register		6002

For MIPLINE and EIPLINE :

 

Ethernet parameters	IP address	Mask	Gateway	DHCP	BootP
	192.168.0.1	255.255.255.0	192.168.0.254	Desactivated	Desactivated

 

 

 

 

3 / 6

• Characteristics

 

 

Communication
Modbus TCP	MIPLINE
Profinet	MPNLINE
Ethernet IP	EIPLINE
Profibus	MPBLINE
Modbus RTU	MRSLINE
Isolation
Supply / RS485-USB-digital output- connector (RJ45 or Sub-D9 or 6 points connector) on the front	4200Vrms, 50Hz, 1mn
USB / RS485 / digital output / connector (RJ45 or Sub-D9 or 6 points connector) on the front	2500Vrms, 50Hz, 1mn
Auxiliary source
Voltage supply	20-240Vdc or 90-230Vac 50/60Hz
General characteristics
Maximum of consumption	MPILINE, MPNLINE, EIPLINE : <7VA MPNLINE, MRSLINE : <6VA
Operating temperature	-10°C … +60°C
Storage temperature	-25°C … +80°C
Protection factor	IP20 Black self-extinguishing polyamide housing V0

 

 

 

Presentation
4개의 격리된 디지털 입력(Dry contacts) 또는 임펄스(NPN, PNP)로 UHLIS 0040T0을 통해 4개 모두를 유연하게 구성할 수 있습니다
모드버스 RTU 연결을 통한 상태 전송 또는 임펄스 카운팅을 위한 입력. UHLIS 0040T0는 5년이 보장됩니다

 

Inputs	Functioning mode	Counting direction	Scale factor value	Counter reset value
	Counting	Increasing	1.0	0.0
	Alarms thresold mode	Alarm 1 thresold	Alarm 1 thresold
	Unused	0.0	0.0
Functions	Function performed	Operand A	Operand B	Operand C
	Unused	Input 1	Input 1	Input 1

 

• Inputs – Communication

 

• Input gauges

 

Input	4 digital inputs: NPN, PNP, dry contacts Acceptable voltage range 0-24V Vil: 2V ; Vih: 10V
Sensor supply	2 wires sensor 24V ; 41mA max
Communication	Isolated USB front panel / Isolated RS485 Modbus RTU

 

• Characteristics

 

Input characteristics
Current input impedance	> 4.7 kΩ Active state >11 MΩ Passive state
Isolation
Supply / Inputs-Communication	4200Vrms, 50Hz,1mn
Input x / Input y / USB-RS485	2500Vrms, 50Hz,1mn
USB / RS485	Without
Auxiliary source
Voltage supply	22-240Vdc or 90-230Vac 50/60Hz
General characteristics
Max frequency of counting / of a digital signal	Counting max frequency: 1 channel: 2.4 kHz ; 2 channels: 2.2 kHz ; 3 channels: 2 kHz ; 4 channels: 1.8 kHz
Maximum of consumption	<5 VA
Operating temperature	-10°C … +60°C
Storage temperature	-25°C … +80°C
Relative humidity	<95% HR (non-condensing)
Protection factor	IP20

 

• Functions

 

Display functions
LED indicators	4 red LEDs light up or down depending on the state of the input 1 LED indicates that a communication is in progress (USB or RS485)
Programming	Programming via USB with IXLOG software
Smart functions
Calculation mode	Functions configurable: A+B, A+B+C, A+B+C+D, A-B, A/B, (A-B)/A
Memorization of Digital input states	Copy status of digital inputs to bits for transmission via Modbus
Counter input	Counting direction: increase, decrease Possibility to enter a multiplier factor on the value of each input Possibility to define 2 alarm thresholds per channel Possibility to reload the counter with an initialization value set when the second threshold is exceeded Reloading a counter with an initialization value by setting a bit
Links and communication
RS485 MODBUS RTU	RS485 MODBUS RTU bidirectional digital link allowing to: recover the measurements and transmit them in digital format configure and control the device
USB front	USB front panel to connect directly to the USB port of a PC for programming via the IXLOG software

 

Presentation
TELIS 9000은 4중 갈바닉 격리, 입력용 24비트 변환 및 출력용 16비트 변환, 열전대 입력용 ± 1°C에서 정확한 콜드 정션 보상을 갖춘 범용 입력 송신기입니다.
TELIS 9000은 5년간 보증됩니다

 

Transmitter with graphical display	Entries*	Sorties						Communication	Width housing (mm)		Transmitter without a graphical display
		Number Analogical		Number Relay
		1	2	1	2	3	4	RS485 USB	22, 5	45
TELIS 9000U0	✓							✓	✓		TELIS 9000T0
TELIS 9000U1	✓	✓						✓	✓		TELIS 9000T1
TELIS 9000U2	✓		✓					✓	✓		TELIS 9000T2
TELIS 9100U0	✓			✓				✓	✓		TELIS 9100T0
TELIS 9150U1	✓	✓		✓				✓	✓		TELIS 9150T1
TELIS 9250U0	✓				✓			✓	✓		TELIS 9250T0
TELIS 9200U0	✓				✓			✓		✓	TELIS 9200T0
TELIS 9200U1	✓	✓			✓			✓		✓	TELIS 9200T1
TELIS 9200U2	✓		✓		✓			✓		✓	TELIS 9200T2
TELIS 9300U0	✓					✓		✓		✓	TELIS 9300T0
TELIS 9300U1	✓	✓				✓		✓		✓	TELIS 9300T1
TELIS 9400U0	✓						✓	✓		✓	TELIS 9400T0
TELIS 9400U1	✓	✓					✓	✓		✓	TELIS 9400T1
TELIS 9400U2	✓		✓				✓	✓		✓	TELIS 9400T2

Current (continuous)	Standard scales: 0-1mA ; 0-10mA ; 0-20mA ; 4-20mA ; ±1mA ; ±10mA ; ±20mA Adjustable scales: from -22 to 22mA
Voltage (continuous)	Standard scales: 0-100mV ; 0-1V ; 0-5V ; 1-5V ; 0-10V ; 2-10V ; ±100mV ; ±1V ; ±5V ; ±10V Standard scales: 0-50V ; 0-100V ; 0-200V ; 0-500V ; 0-1000V ; ±50V ; ±100V ; ±200V ; ±500V ; ±1000V Adjustable scales: From -110 to 110mV, from -2 to 11V Adjustable scales: From -1000 to 1000V
Variable resistance thermometer	Standard scales: CU50 ; CU53 ; CU100 PT10 ; PT100 ; PT1000 ; Ni100 ; Ni1000 2 or 3 wires Adjustable scales: CU50 ; CU53 ; CU100 PT10 ; PT100 ; PT1000 ; Ni100 ; Ni1000 2 or 3 wires
Resistance 2 wires	Standard scales: 200Ω ; 1KΩ ; 10KΩ ; 50KΩ
Special table for NTC PTC	Adjustable scales: 200Ω ; 1KΩ ; 10KΩ ; 50KΩ Programmable with IXLOG software Unit: °C or °F
Thermocouple	Standard scales: J, K, R, S, T, E, B, N, W3/D, W5/C, Mo, P Adjustable scales: J, K, R, S, T, E, B, N, W3/D, W5/C, Mo, P Unit: °C or °F Cold junction compensation: internal or external
Potentiometer	From 0-100Ω to 0-100KΩ Other values on request
Sensor supply	2 or 3 wires sensor 24V – 32mA max Only in 1 channel input mode

Output Gauges

Output Current	Standard scales : 0-20mA ; 4-20mA Adjustable scales : From 0 to 22mA
Output Voltage	Standard scales : 0-10V Adjustable scales : From 0 to 11V Possible assignment I (ULCOS 6XXIX) / V ULCOS 6XXVX) or F
Output Relay	Relay 1RT – Max current : 500mA Max voltage : 250Vac/220Vdc – Max power : 60Vac/30W Possible assignment I (ULCOS 6XXIX) / V ULCOS 6XXVX) or F
Communication	Output Current 1 & 2	Standard scales: 0-10mA ; 0-20mA ; 4-20mA Adjustable scales: from 0 to 20mA
	Output Voltage 1	Standard scales: 0-10V ; ±10V (except TELIS 9150X1 and TELIS 9300X1) ; 0-5V ; 1-5V ; 2-10V Adjustable scales: from -10 to 10V (except TELIS 9150X1 and TELIS 9300X1)
	Output Voltage 2	Standard scales: 0-5V ; 1-5V ; 2-10V ; 0-10V Adjustable scales: from 0 à 10V
	Output Relay	Relay 1RT or 1T: 2A-250Vac
	Communication	Isolated USB in Front Panel / Isolated RS485 Modbus RTU

Technical Data

Characteristics

Display
Type	Non backlit LCD
Color	Green
Number of characters	4
Numbers of lines	4
Programming joystick	5 positions
Input characteristics
Current input impedance	on CT
Voltage input impedance	>10MΩ
Frequency	From 40Hz to 70Hz From 360 to 440Hz
Maximum measurable voltage	ULCOS 6XXVX : 1000V
Maximum measurable current	ULCOS 6XXIX : 6,5A
Overload	ULCOS 6XXIX :      50A maximum for 1S 10A maximum permanent
Output characteristics
Permissible impedance on the current output	<900Ω
Permissible impedance on the voltage output	>800Ω
Isolation
Supply / Input – Output1 – Output2 – USB	4200Vrms, 50Hz, 1mn
Input / Output1 – Output2	2500Vrms, 50Hz, 1mn
Input / USB	Without
Output1 – Output2 / USB	2500Vrms, 50Hz. 1mn
Output1 / Output2	Without
Auxiliary source
Voltage supply	22-240Vdc or 90-230Vac 50/60Hz
General characteristics
Precision class	0,25
Input analog/digital conversion	24 bits
Output analog/digital conversion	16 bits
Response time	<200ms
RMS	True up to rank 11
Thermal drift	<25ppm
Residual ripple on current output	<20μA
Residual ripple on voltage output	<10mV
Maximum of consumption	<7VA
Operating temperature	-10°C … +60°C
Storage temperature	-25°C … +80°C
Protection factor	Display
	Type	Backlit LCD
	Color	Blue
	Number of characters	5
	Numbers of lines	5
	Programming joystick	5 positions
	Input characteristics
	Current input impedance	5.6Ω
	Voltage input impedance	U<10V: >10MΩ U±10V ou >10V: 6MΩ
	Current input PT100 ; Ni100	Current: <1mA
	Current input PT1000 ; Ni1000	Current: <0.8mA
	Current input resistance 2 wires R=200Ω ; R=1kΩ	Current: <1mA
	Current input resistance 2 wires R=10kΩ	Current: <0.2mA
	Output characteristics
	Permissible impedance on the current output	Output 1 & 2: <1kΩ
	Permissible impedance on the voltage output	Output 1 & 2: >1kΩ
	Isolation
	Supply / Input-Output(s)-Relay- RS485-USB	4200Vrms, 50Hz, 1mn
	Input / Output 1 / Output 2 / Relay / RS485	2500Vrms, 50Hz, 1mn
	USB / Input	2500Vrms, 50Hz, 1mn
	USB / Output 2	Without
	USB / Output 1-relay	2500Vrms, 50Hz, 1mn
	USB / RS485	2500Vrms, 50Hz, 1mn
	Auxiliary source
	Voltage supply	22-240Vdc or 90-230Vac 50/60Hz

Presentation
이러한 아날로그 송신기는 0…4…20mA – 0…4…20mA의 두 가지 범위에서 사용할 수 있습니다:
• EOLIS 0030A2는 이중 격리기입니다. 각 독립 채널에는 센서 전원 공급 장치가 있는 입력 0…4…20mA와 전류 출력 0…4…20mA가 있습니다.
• EOLIS 0030A2- F는 이중 격리기입니다. 각 독립적이고 격리된 채널에는 센서 전원 공급 장치가 있는 입력 0…4…20mA와 낙뢰 충격 보호 장치가 있는 전류 출력 0…4…20mA가 있습니다
EOLIS 0030A2는 5년간 보증됩니다.

 

Applications

EOLIS 0030A2 & EOLIS 0030A2F는 격리 및 신호 조절을 위한 인터페이스로 사용하도록 특별히 설계되었습니다:
• 센서와 PLC.
• PLC 및 액추에이터.
배선, 시운전, 작동 및 유지보수를 용이하게 하기 위해 JM Concept는 사전 배선판인 BASEL(나사 또는 스프링 적재)을 개발했습니다.
BASELINE은 또한 도체 케이블을 통해 PLC에 직접 연결할 수 있는 SUBD 연결이 있습니다. 이 솔루션은 구현을 용이하게 하고 케이블 연결 시간을 단축하며 시스템 신뢰성을 높입니다.

• Factory settings

 

Channel 1	Channel 2
Input : 4-20mA	Input : 4-20mA
Output : 4-20mA	Output : 4-20mA

Other settings on demand

 

• Inputs – Outputs

Possible settings for EOLIS 0030A2 : Input 0-20mA / Output 0-20mA Input 4-20mA / Output 0-20mA Input 4-20mA / Output 4-20mA

• Input gauges

 

Current (continuous)	0-20mA ; 4-20mA
Sensor supply	Sensor 2 wires 24Vdc ; Supply Sensor : 24V – 26mA max

Output gauges

Current

0-20mA ; 4-20mA

• Characteristics

 

Inputs characteristics
Current input impedance	4,75Ω
Output characteristics
Permissible impedance on the current output 1 & 2	<1kΩ
Isolation
Supply / Input(s)-Output(s)	4200Vrms, 50Hz, 1mn
Input(s) / Output(s)	1500Vrms, 50Hz, 1mn
Input x / Input y	2500Vrms, 50Hz, 1mn
Output x / Output y	2500Vrms, 50Hz, 1mn
Auxiliary source
Voltage supply	22-240Vdc or 90-230Vac 50/60Hz
General characteristics
Precision Class	0,1
Response time	<3ms
Thermal drift	<50ppm
Maximum of consumption	<7VA
Operating temperature	-10°C … +60°C
Storage temperature	-25°C … +80°C
Protection factor	IP20 Black self-extinguishing polyamide housing V0

 

Presentation
ULCOS 600은 1 또는 2개의 아날로그 출력과 2개의 릴레이 출력을 가질 수 있는 교류 또는 전압 입력을 위한 컨버터 입니다.
ULCOS 600은 10년의 보증기간을 제공합니다.

Input Gauges

Converter	Inputs		Outputs			Communication
			Number of Analog		Number of Relay
	Alternating current	Alternating voltage	1	2	2	Indirect USB
ULCOS 600I1	√		√			√
ULCOS 620I2	√			√	√	√
ULCOS 600V1		√	√			√
ULCOS 620V2		√		√	√	√

Input Gauges

Alternating current ULCOS 6XXIX	Standard scales : 0-1A ; 0-5A Adjustable scales : From 0 to 6,5A
Alternating voltage ULCOS 6XXVX	Standard scales : 0-10V ; 0-50V ; 0-120V ; 0-250V ; 0-500V Adjustable scales : From 0 to 1000V
External CT choice	Value : 1-9999 or 5-9999KA
External VT choice	Value : 1-9999KV

Output Gauges

Output Current	Standard scales : 0-20mA ; 4-20mA Adjustable scales : From 0 to 22mA
Output Voltage	Standard scales : 0-10V Adjustable scales : From 0 to 11V Possible assignment I (ULCOS 6XXIX) / V ULCOS 6XXVX) or F
Output Relay	Relay 1RT – Max current : 500mA Max voltage : 250Vac/220Vdc – Max power : 60Vac/30W Possible assignment I (ULCOS 6XXIX) / V ULCOS 6XXVX) or F
Communication	USB Cable (ULCOS 100) on Front Panel

Characteristics

Display
Type	Non backlit LCD
Color	Green
Number of characters	4
Numbers of lines	4
Programming joystick	5 positions
Input characteristics
Current input impedance	on CT
Voltage input impedance	>10MΩ
Frequency	From 40Hz to 70Hz From 360 to 440Hz
Maximum measurable voltage	ULCOS 6XXVX : 1000V
Maximum measurable current	ULCOS 6XXIX : 6,5A
Overload	ULCOS 6XXIX :     50A maximum for 1S 10A maximum permanent
Output characteristics
Permissible impedance on the current output	<900Ω
Permissible impedance on the voltage output	>800Ω
Isolation
Supply / Input – Output1 – Output2 – USB	4200Vrms, 50Hz, 1mn
Input / Output1 – Output2	2500Vrms, 50Hz, 1mn
Input / USB	Without
Output1 – Output2 / USB	2500Vrms, 50Hz. 1mn
Output1 / Output2	Without
Auxiliary source
Voltage supply	22-240Vdc or 90-230Vac 50/60Hz
General characteristics
Precision class	0,25
Input analog/digital conversion	24 bits
Output analog/digital conversion	16 bits
Response time	<200ms
RMS	True up to rank 11
Thermal drift	<25ppm
Residual ripple on current output	<20μA
Residual ripple on voltage output	<10mV
Maximum of consumption	<7VA
Operating temperature	-10°C … +60°C
Storage temperature	-25°C … +80°C
Protection factor	IP20 Black self-extinguishing polyamide housing V0